رقم الموديل WEO012832F
◄Thinner version OLED
◄النوع: جرافيك
◄االهيكل: COG
◄الحجم: 0.91 بوصة
◄مصفوفة نقطية 128*32
◄وحدة تحكم مدمجة SSD1306B
◄مزود طاقة +3 فولت
◄1/32 حمولة
◄الواجهة:I2C
◄لون العرض: أبيض / أصفر / أزرق سماوي
الرسم
Data source ref: WEO012832FWPP3N00001
المواصفات
وظيفة دبوس واجهة التوصيل
| .No | الرمز | الوظيفة |
|---|---|---|
| 1 | C2P | .Positive Terminal of the Flying Inverting CapacitorNegative Terminal of the Flying Boost CapacitorThe charge-pump capacitors are required between the terminals. They must be floated when the converter is not used |
| 2 | C2N | |
| 3 | C1P | |
| 4 | C1N | |
| 5 | VBAT | Power Supply for DC/DC Converter Circuit .This is the power supply pin for the internal buffer of the DC/DC voltage converter. It must be connected to external source when the converter is used. It should be connected to VDD when the converter is not used |
| 6 | NC | No connection |
| 7 | VSS | Ground of Logic Circuit .This is a ground pin. It acts as a reference for the logic pins. It must be connected to external ground |
| 8 | VDD | Power Supply for Logic .This is a voltage supply pin. It must be connected to external source |
| 9 | #RES | Power Reset for Controller and Driver .This pin is reset signal input. When the pin is low, initialization of the chip is executed |
| 10 | SCL | .I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin inapplication and D0 is the serial clock input, SCL |
| 11 | SDA | |
| 12 | IREF | Current Reference for Brightness Adjustment .This pin is segment current reference pin. A resistor should be connected between this pin and VSS. Set the current lower than 12.5μA |
| 13 | VCOMH | Voltage Output High Level for COM Signal .This pin is the input pin for the voltage output high level for COM signals. A capacitor should be connected between this pin and VSS |
| 14 | VCC | Power Supply for OEL Panel .This is the most positive voltage supply pin of the chip. A stabilization capacitor should be connected between this pin and VSS when the converter is used. It must be connected to external source when the converter is not used |
المواصفات العامة
| العنصر | الأبعاد | الوحدة |
|---|---|---|
| مصفوفة نقطية (قة العرض) | 128 × 32 | نقطة |
| أبعاد الوحدة | 30.0 × 11.5 × 1.26 | mm |
| المنطقة النشطة | 22.384 × 5.584 | mm |
| حجم النقطة | 0.152 × 0.152 | mm |
| درجة النقطة | 0.175 × 0.175 | mm |
| وضع العرض | مصفوفة موجبة | |
| لون العرض | أحادية اللون | |
| Drive Duty | 1/32 حمولة | |
| IC | SSD1306 | |
| الواجهة | I2C | |
| الحجم (القطر) | 0.91 بوصة | |
تصنيفات الحد الأقصى المطلق
| Parameter | الرمز | أدنى قيمة | أقصى قيمة | الوحدة |
|---|---|---|---|---|
| Supply Voltage for Logic | VDD | 0 | 4.0 | V |
| Supply Voltage for Display | VCC | 0 | 16.0 | V |
| درجة حرارة التشغيل | TOP | -40 | +80 | °C |
| درجة حرارة التخزين | TSTG | -40 | +85 | °C |
المميزات الإلكترونية
DC المميزات الإلكترونية
| العنصر | الرمز | الحالة | أدنى قيمة | القيمة النموذجية | أقصى قيمة | الوحدة |
|---|---|---|---|---|---|---|
| Supply Voltage for Logic | VDD | － | 2.8 | 3.0 | 3.3 | V |
| Supply Voltage for Display | VCC | － | 7 | 7.25 | 8 | V |
| .Input High Volt | VIH | － | 0.8×VDD | － | VDDIO | V |
| .Input Low Volt | VIL | － | 0 | － | 0.2×VDD | V |
| .Output High Volt | VOH | － | 0.9×VDD | － | VDDIO | V |
| .Output Low Volt | VOL | － | 0 | － | 0.1×VDD | V |
| (Operating Current for VCC (VCC Supplied Externally | ICC | Vcc =7.25V | － | 7 | 11 | mA |
Search keyword: 128x32 oled, oled 128x32, 0.91 oled, 0.91" oled, 0.91 inch oled, oled 0.91, oled 0.91"
