0.91 inç OLED Ekran, 128x32 OLED Ekran, COG OLED Ekran

0.91 inç, 128x32 COG OLED Ekran

Model No. WEO012832D

►2017 Taiwan Excellence Award
►Türü : Grafik (Çerçevesiz)
►Yapı : COG
►Boyut : 0.91 inç
►Suitable for wearable device
►128 x 32 dot matrisi
►Kontrolör dahil SSD1306
►3V güç sağlayıcı
►1/32 görev
►Ara yüz : SPI
►OLED Rengi: Beyaz / Sarı / Gök Mavisi
►Other FPC options available in below table

PDF İndir

DEMO CODE

Sorguya ekle

Önceki Listeye geri dön Sonraki

TANIM

ÇIZIM

OLED 128x32, 128x32 OLED Display, 0.91 inch OLED - WEO012832D

Data source ref: WEO012832DWPP3N00008

AYRINTILAR

Arayüz Pin Fonksiyonlari

No.	Sembol	Fonksiyon
1	C2P	Positive Terminal of the Flying Inverting CapacitorNegative Terminal of the Flying Boost CapacitorThe charge-pump capacitors are required between the terminals. They must be floated when the converter is not used.
2	C2N
3	C1P
4	C1N
5	VBAT	Power Supply for DC/DC Converter Circuit This is the power supply pin for the internal buffer of the DC/DC voltage converter. It must be connected to external source when the converter is used. It should be connected to VDD when the converter is not used.
6	VSS	Ground of Logic Circuit This is a ground pin. It acts as a reference for the logic pins. It must be connected to external ground.
7	VDD	Power Supply for Logic This is a voltage supply pin. It must be connected to external source.
8	CS#	Chip Select This pin is the chip select input. The chip is enabled for MCU communication only when CS# is pulled low.
9	RES#	Power Reset for Controller and Driver This pin is reset signal input. When the pin is low, initialization of the chip is executed.
10	D/C#	Data/Command Control This pin is Data/Command control pin.. When the pin is pulled high and serial interface mode is selected, the data at SDIN is treated as data. When it is pulled low, the data at SDIN will be transferred to the command register. In I2C mode, this pin acts as SA0 for slave address selection.
11	SCLK	When serial mode is selected, D1 will be the serial data input SDIN and D0 will be the serial clock input SCLK.
12	SDIN
13	IREF	Current Reference for Brightness Adjustment This pin is segment current reference pin. A resistor should be connected between this pin and VSS. Set the current lower than 12.5μA.
14	VCOMH	Voltage Output High Level for COM Signal This pin is the input pin for the voltage output high level for COM signals. A capacitor should be connected between this pin and VSS.
15	VCC	Power Supply for OEL Panel This is the most positive voltage supply pin of the chip. A stabilization capacitor should be connected between this pin and VSS when the converter is used. It must be connected to external source when the converter is not used.

Genel Özellikler

Kalem	Ölçü	Birim
Nokta Matrisi (Çözünürlük)	128 × 32	dot
Modül ölçüleri	30.0 × 11.5 × 1.26	mm
Aktif alan	22.384 × 5.584	mm
Nokta boyutu	0.152 × 0.152	mm
Nokta sıklığı	0.175 × 0.175	mm
Display Mode	Pasif Matrisli
Display Color	Monokrom
Drive Duty	1/32 Duty
IC	SSD1306
Arayüz	4-wire SPI
Boyut (Köşegen)	0.91 inç

Maksimum Değerler

Parameter	Sembol	Minumum Deger	Maksimum Deger	Birim
Supply Voltage for Logic	VDD	0	4.0	V
Supply Voltage for Display	VCC	0	16.0	V
Çalışma Sıcaklığı	TOP	-40	+80	°C
Storage Temperature	TSTG	-40	+85	°C

Elektronik Özellikleri

DC Elektronik Özellikleri

Kalem	Sembol	Durum	Minumum Deger	Tipik Deger	Maksimum Deger	Birim
Supply Voltage for Logic	VDD	－	2.8	3.0	3.3	V
Supply Voltage for Display	VCC	－	7	7.25	8	V
Input High Volt.	VIH	－	0.8×VDD	－	VDDIO	V
Input Low Volt.	VIL	－	0	－	0.2×VDD	V
Output High Volt.	VOH	－	0.9×VDD	－	VDDIO	V
Output Low Volt.	VOL	－	0	－	0.1×VDD	V
Operating Current for VCC (VCC Supplied Externally)	ICC	Vcc =7.25V	－	7	11	mA

FPC options

FPC Length	PIN	pitch	ZIF FPC or HOTBAR FPC	Interface	FPC No.	Create Date
17.06	15	0.65	HOTBAR FPC	SPI	FPC2065001501XXXXX00	20140827
40.76	15	0.5	ZIF FPC	SPI	FPC2050001511XXXXX02	20150421
11.26	14	0.62	HOTBAR FPC	I2C	FPC2062001401XXXXX02	20160106

Search keyword: 128x32 oled, oled 128x32, 0.91 oled, 0.91" oled, 0.91 inç oled, oled 0.91, oled 0.91"