Accueil Produits Afficheur COG WO12864U
Afficheurs et modules LCD ‘Chip-On-Glass’ 128x64
Afficheurs et modules LCD ‘Chip-On-Glass’ 128x64
Afficheurs et modules LCD ‘Chip-On-Glass’ 128x64
Afficheurs et modules LCD ‘Chip-On-Glass’ 128x64

Afficheurs et modules LCD ‘Chip-On-Glass’ 128x64

N° de modèle WO12864U

►Afficheur COG 128x64
►Afficheur graphique
►Contrôleur intégré ST7565P
►Alimentation 3.3V
►Taux de rafraichissement 1/64 duty cycle, 1/9 bias
►Interface : 6800/8080/SPI

Téléchargement PDF
DEMO CODE
Ajouter à demande
PRÉC. Retour à la liste SUIVANT

DESCRIPTION

DESSIN

WO12864U

SPÉCIFICATIONS

Fonction PIN sur l'interface

Pin No. Symbole I/O Description
1 VDD ­_ Power supply pin for logic.
2 VSS _ Ground pin, connected to 0V
3 /CS1 I Chip select input pin. Interface access is enabled when CS1B is "L" and CB2 is "H" . When chip is on-active (CS1B="H" or CS2="L"), D[7:0] pins are high impedance.
4 CS2
5 /RES I Hardware reset input pin. When RSTB is "L", internal initialization is executed and the internal registers will be initialized.
6 A0 I It determines whether the access is related to data or command.
A0=“H”: Indicates that signals on D[7:0] are display data.
A0=“L”: Indicates that signals on D[7:0] are command.
7 R/W I Read/Write execution control pin. When PSB is "H",
C86 MPU Type RWR Description
H 6800 series R/W Read/Write control input pin.
R/W="H": read
R/W="L": write
L 8080 series /WR Write enable input pin.
Signals on D[7:0] will be latched at the rising edge of /WR signal.

RWR is not used in serial interface and should fix to "H" by VDD.
8 E I Read/Write execution control pin. When PSB is "H",
C86 MPU Type ERD Description
H 6800 series E Read/Write control input pin.
R/W="H": When E is "H", D[7:0] are in output mode.
R/W="L": Signals on D[7:0] are latched at the falling edge of E signal
L 8080 series /RD Read enable input pin.
When /RD is "L", D[7:0] are in output mode.

ERD is not used in serial interface and should fix to "H" by VDD.
9-16 D0-D7 I/O Data bus line
17 C86 I C86 selects the microprocessor type in parallel interface mode.
PSB C86 Selected Interface
"H" "H" Parallel 6800 Series MPU Interface
"H" "L" Parallel 8080 Series MPU Interface
"L" "X" Serial 4-Line SPI Interface

Please refer to “APPLICATION NOTES” and “Microprocessor Interface” (Section 6) for detailed connection of the selected interface.
18 P/S I PSB selects the interface type: Serial or Parallel.

Spécifications générales

Article Dimensions Unité
Matrice de points (Résolution) 128 × 64 －
Dimensions du module 58.2 × 44.7 × 3.9(MAX) mm
Zone d'affichage 52.0 × 33.5 mm
Zone active 47.76 × 30.29 mm
Taille des points 0.40 × 0.35 mm
Pas des points 0.42 × 0.37 mm
Duty 1/64
Type de rétroéclairage LED
IC ST7565P

Valeurs nominales maximales absolues

Article Symbole Valeur min Valeur type Valeur max Unité
Température de fonctionnement TOP -20 － +70 ℃
Température de stockage TST -30 － +80 ℃
Power Supply Voltage VDD -0.3 － 3.6 V
Power supply voltage (VDD standard) V0, VOUT -0.3 － 14.5 V
Power supply voltage (VDD standard) V1, V2, V3, V4 -0.3 － V0+0.3 V

Caractéristiques électroniques

Article Symbole État Valeur min Valeur type Valeur max Unité
Supply Voltage For Logic VDD-VSS － 3.0 － 3.3 V
Supply Voltage For LCD VOP Ta=-20℃
Ta=25℃
Ta=70℃		 －
8.3
－		 －
8.5
－		 －
8.7
－		 V
V
V
Input High Volt. VIH － 0.8VDD － VDD V
Input Low Volt. VIL － VSS － 0.2VDD V
Output High Volt. VOH － 0.8VDD － VDD V
Output Low Volt. VOL － VDD － 0.2VDD V
Supply Current IDD VDD=3.3V － 1 2 mA
 

Search Keyword: lcd 128x64, lcd 128 x 64, 128x64 lcd, 128 x 64 lcd

go top
close