Strona główna Produkty Wyświetlacz TFT Wyświetlacz TFT Standardowe WF57ETIACDNGF

Wyświetlacz TFT 5.7 cali (Pojemnościowy Panel Dotykowy)

Numer modelu WF57ETIACDNGF

►Rozmiar : 5.7 cali
►Rozdzielczość : 320 x 240 punktów
►Godzina obserwacji : 12H
►Interfejs : RGB
►Wbudowany kontroler : --
►Płyta kontrolera : opcjonalnie
►jasność (cd/m²) : 700
►Otwory w ramie : Yes
►Panel dotykowy : Pojemnościowy panel dotykowy (PCAP)
►Detect Point : 5 Fingers
►O-Film : opcjonalnie

Rysunek

5.7 inch Projected Capacitive Touch Display - WF57ETIACDNGF - Winstar Display

Specyfikacja

Funkcja pinów interfejsu

LCM PIN Definition

Pin Symbol Funkcja
1 IF1 Input data format control
2 IF2 Input data format control
3 POL Polarity Signal connect to VCOM driving circuit.
4 RESET Hardware reset
5 SPENA Chip select
6 SPCL Serial Clock
7 SPDA Serial Data
8 B0 Blue Data bit
9 B1 Blue Data bit
10 B2 Blue Data bit
11 B3 Blue Data bit
12 B4 Blue Data bit
13 B5 Blue Data bit
14 B6 Blue Data bit
15 B7 Blue Data bit
16 G0 Green Data bit
17 G1 Green Data bit
18 G2 Green Data bit
19 G3 Green Data bit
20 G4 Green Data bit
21 G5 Green Data bit
22 G6 Green Data bit
23 G7 Green Data bit
24 R0 Red Data bit
25 R1 Red Data bit
26 R2 Red Data bit
27 R3 Red Data bit
28 R4 Red Data bit
29 R5 Red Data bit
30 R6 Red Data bit
31 R7 Red Data bit
32 Hsync Horizontal synchronous signal
33 Vsync Vertical synchronous signal
34 Data CLK Dot data clock
35 AVDD(analog) Analog power: 4.5V~5.5V
36 AVDD(analog) Analog power: 4.5V~5.5V
37 VCC(Digital) Digital power: 3V~3.6V
38 VCC(Digital) Digital power: 3V~3.6V
39 NPC NTSC/PAL mode Auto detection result H:NTSC/L:PAL
40 VGL Gate off power
41 VGL Gate off power
42 UD Up/down selection
43 VGH Gate on power
44 LRC Shift direction of device internal shift register control.
45 GND System ground pin of the IC.Connect to system ground.
46 VCOM VCOM driving input
47 VCOM VCOM driving input
48 ENB Signal to settle the horizontal display position
49 GND System ground pin of the IC.Connect to system ground.
50 GND System ground pin of the IC.Connect to system ground.

PCAP PIN Definition

Pin Symbol Funkcja
1 VSS Ground for analog circuit
2 VDDT Power Supply : +3.3V
3 SCL I2C clock input
4 NC No connect
5 SDA I2C data input and output
6 NC No connect
7 /RST External Reset, Low is active
8 NC No connect
9 /INT External interrupt to the host
10 VSS Ground for analog circuit

Ogólna specyfikacja

Rzecz Wymiar Jednostka
Rozmiar 5.7 cali
Matryca punktowa 320 × RGB × 240 (TFT) punktowy
Wymiary modułu 141.12 × 101.55 × 8.235 mm
Obszar aktywny 115.2 × 86.4 mm
Raster pomiędzy pikselami 0.12 × 0.36 mm
Rodzaj LCD TFT, biały, Transmisyjny
TFT Interfejs 24-bit RGB
godzina obserwacji 12 o'clock
Kierunek inwersji skali szarości 6 o'clock
Proporcje 4:3
PCAP IC FT5426 albo odpowiednik
PCAP Interfejs I2C
PCAP FW Wersja FN058A001_FT5426__V03_20180910_all.bin
Rodzaj podświetlenia LED, biały
Panel dotykowy PCAP,Pojemnościowy panel dotykowy
Powierzchnia Glare

Bezwzględne oceny maksymalne

Rzecz Symbol Minimalna wartość Typowa wartość Maksymalna wartość Jednostka
Temperatura pracy TOP -20 +70
Temperatura przechowywania TST -30 +80

Parametry elektryczne

Rzecz Symbol Stan Minimalna wartość Typowa wartość Maksymalna wartość Jednostka
Supply Voltage For Logic VCC 3.0 3.3 3.6 V
Supply Voltage For Touch Logic VDDT- - 2.8 - 3.3 V
Input High Volt. VIH 0.7 Vcc Vcc V
Input Low Volt. VIL 0 0.3 Vcc V
LCD Driving Supply Voltage VGH x 1 Ta=25℃ - 15 - V x 3
VGL x 2 - -10 -
VcomH 2.5 - 5.5
VcomL -2.0 - 0
Supply Current IVCC VCC=3.3V 5 8 mA

Ostatnio oglądane

go top
close