2.4 inç Ekran IPS TFT 240x320

Model No. WF24LTYAJDNN0

►Boyut : 2.4"
►Çözünürlük : 240 x 320 dot
►Görünüm yönü : IPS
►Ara yüz : MCU, SPI
►Kontrolör dahil: ILI9341V
►Kontrol Kart : Hayır
►Parlaklık(cd/m²): 500
►Delikli Çerçeve: Hayır
►Dokunmatik Ekran: dokunmatik Panel olmadan

PDF İndir

DEMO CODE

Sorguya ekle

Önceki Listeye geri dön Sonraki

ÇIZIM

2.4" IPS Color TFT Module - WF24LTYAJDNN0 - Winstar Display

AYRINTILAR

Arayüz Pin Fonksiyonlari

NO	Sembol	Fonksiyon	I/O
1	GND	Ground	P
2-6	NC	No connection	-
7	VCI	High voltage power supply for analog circuit blocks (2.5 ~ 3.3 V)	P
8	IOVCC	Low voltage power supply for interface logic circuits (1.65 ~ 3.3 V)	P
9	TE	Tearing effect output pin to synchronize MPU to frame writing, activated by S/W command. When this pin is not activated, this pin is low. If not used, open this pin.	O
10	CS	Chip select signal.	I
11	D/CX(SCL)	(D/CX): This pin is used to select “Data or Command” in the parallel interface. When DCX = 1, data is selected. When DCX = 0, command is selected. (SCL): This pin is used as the serial interface clock in 3-wire 9-bit/4-wire 8-bit serial data interface. If not used, this pin should be connected to VDDI or VSS.	I
12	WR(SPI_D/C)	(WRX) - 8080-Ⅰ/8080-Ⅱ system: Serves as a write signal and writes data at the rising edge. (D/CX) - 4-line system: Serves as the selector of command or parameter. Fix to VDDI level when not in use.	I
13	RD	8080-Ⅰ/8080-Ⅱ system (RDX): Serves as a read signal and MCU read data at the rising edge. Fix to VDDI level when not in use.	I
14-29	DB0~DB15	18-bit parallel bi-directional data bus for MCU system and RGB interface mode Fix to VSS level when not in use.	I/O
30	RESET	This signal will reset the device and must be applied to properly initialize the chip. Signal is active low.	I
31	IM0	Select the MCU interface mode MPU Parallel interface bus and serial interface select If use RGB Interface must select serial interface. * : Fix this pin at VDDI or VSS.	I
32	IM1
33	IM2
34	DB16	18-bit parallel bi-directional data bus for MCU system and RGB interface mode Fix to VSS level when not in use.	I/O
35	DB17		I/O
36	LEDK	Cathode of LED backlight.	P
37	LEDK	Cathode of LED backlight.	P
38	LEDA	Anode of LED backlight.	P
39	SDI(SDA)	When IM[3] : Low, Serial in/out signal. When IM[3] : High, Serial input signal. The data is applied on the rising edge of the SCL signal. If not used, fix this pin at VDDI or VSS.	I/O
40	SDO	Serial output signal. The data is outputted on the falling edge of the SCL signal. If not used, open this pin	O

Genel Özellikler

Kalem	Ölçü	Birim
Boyut (Köşegen)	2.4	inç
Nokta Matrisi (Çözünürlük)	240 × RGB × 320(TFT)	dot
Modül ölçüleri	42.72(W) × 60.26(H) × 2.8(D)	mm
Aktif alan	36.72 × 48.96	mm
Nokta sıklığı	0.153 × 0.153	mm
LCD Tipi	TFT, Siyah, İletici
Kontrolör IC	ILI9341V veya eşdeğer
Görünüm yönü	80/80/80/80
Görünüm Oranı	Portrait
Backlight Tipi	LED, Beyaz
Dokunmatik Panel	Dokunmatik Panel olmadan
Yüzey	Parlama