رقم الموديل WEO006432A
◄النوع: جرافيك
◄الهيكل: COG
◄الحجم: 0.49 بوصة
◄مصفوفة نقطية 64*32
◄وحدة تحكم مدمجة SSD1306
◄مزود طاقة +3 فولت
◄1/32 دورة الحمولة
◄الواجهة: I2C
◄لون العرض: أبيض / أصفر / أزرق سماوي
الرسم
المواصفات
وظيفة دبوس واجهة التوصيل
| .No | الرمز | الوظيفة |
|---|---|---|
| 1 | C2N | Positive Terminal of the Flying Inverting Capacitor Negative Terminal of the Flying Boost Capacitor The charge-pump capacitors are required between the terminals. They must be floated when the converter is not used |
| 2 | C2P | |
| 3 | C1P | |
| 4 | C1N | |
| 5 | VBAT | Power Supply for DC/DC Converter Circuit This is the power supply pin for the internal buffer of the DC/DC voltage converter. It must be connected to external source when the converter is used. It should be connected to VDD when the converter is not used |
| 6 | NC | No connection |
| 7 | VSS | Ground of Logic Circuit .This is a ground pin. It acts as a reference for the logic pins. It must be connected to external ground |
| 8 | VDD | Power Supply for Logic .This is a voltage supply pin. It must be connected to external source |
| 9 | #RES | Power Reset for Controller and Driver .This pin is reset signal input. When the pin is low, initialization of the chip is executed |
| 10 | SCL | Host Data Input/Output Bus When serial mode is selected, D1 will be the serial data input SDIN and D0 will be the serial clock input SCLK. When I2C mode is selected, D2 & D1 should be tired together and serve as SDAout & SDAin in application and D0 is the serial clock input SCL |
| 11 | SDA | |
| 12 | IREF | Current Reference for Brightness Adjustment .This pin is segment current reference pin. A resistor should be connected between this pin and VSS. Set the current lower than 12.5μA |
| 13 | VCOMH | Voltage Output High Level for COM Signal .This pin is the input pin for the voltage output high level for COM signals. A capacitor should be connected between this pin and VSS |
| 14 | VCC | Power Supply for OEL Panel This is the most positive voltage supply pin of the chip. A stabilization capacitor should be connected between this pin and VSS when the converter is used. It must be connected to external source when the converter is not used |
البيانات الميكانيكية
| العنصر | الأبعاد | الوحدة |
|---|---|---|
| مصفوفة نقطية | 64 × 32 | نقطة |
| أبعاد الوحدة | 14.5 × 11.6 × 1.26 | mm |
| المنطقة النشطة | 11.18 × 5.58 | mm |
| حجم النقطة | 0.153 × 0.153 | mm |
| درجة النقطة | 0.175 × 0.175 | mm |
| وضع العرض | مصفوفة موجبة | |
| لون العرض | أحادية اللون | |
| Drive Duty | 1/32 حمولة | |
| IC | SSD1306 | |
تصنيفات الحد الأقصى المطلق
| Parameter | الرمز | أدنى قيمة | أقصى قيمة | الوحدة |
|---|---|---|---|---|
| Supply Voltage for Logic | VDD | 0 | 4 | V |
| Supply Voltage for Display | VCC | 0 | 15 | V |
| درجة حرارة التشغيل | TOP | -40 | +80 | °C |
| درجة حرارة التخزين | TSTG | -40 | +80 | °C |
المميزات الإلكترونية
| العنصر | الرمز | الحالة | أدنى قيمة | القيمة النموذجية | أقصى قيمة | الوحدة |
|---|---|---|---|---|---|---|
| Supply Voltage for Logic | VDD | － | 2.8 | 3 | 3.3 | V |
| Supply Voltage for Display | VCC | － | 7 | 7.5 | 7.8 | V |
| Input High Volt | VIH | － | 0.8×VDD | － | VDDIO | V |
| Input Low Volt | VIL | － | 0 | － | 0.2×VDD | V |
| Output High Volt | VOH | － | 0.9×VDD | － | VDDIO | V |
| Output Low Volt | VOL | － | 0 | － | 0.1×VDD | V |
| 50% Check Board operating Current | ICC | VCC=7.5V | － | 5 | 20 | mA |
"Search keyword: 64x32 oled, oled 64x32,0.49 oled, 0.49" oled, 0.49 inch oled, oled 0.49, oled 0.49
