Graficzne OLED 64x32, 0.49"
Numer modelu WEO006432A
►Typ: graficzny
►Struktura: COG
►Rozmiar: 0.49"
►64x32 matryca punktowa
►wbudowany kontroler SSD1306
►zasilanie 3V
►wypełnienie 1/32
►Interfejs: I2C
►Kolor wyświetlacza: biały / żółto / jasnoniebieski
Rysunek
Specyfikacja
Funkcja pinów interfejsu
| No. | Symbol | Funkcja |
|---|---|---|
| 1 | C2N | Positive Terminal of the Flying Inverting Capacitor Negative Terminal of the Flying Boost Capacitor The charge-pump capacitors are required between the terminals. They must be floated when the converter is not used. |
| 2 | C2P | |
| 3 | C1P | |
| 4 | C1N | |
| 5 | VBAT | Power Supply for DC/DC Converter Circuit This is the power supply pin for the internal buffer of the DC/DC voltage converter. It must be connected to external source when the converter is used. It should be connected to VDD when the converter is not used. |
| 6 | NC | No connection. |
| 7 | VSS | Ground of Logic Circuit This is a ground pin. It acts as a reference for the logic pins. It must be connected to external ground. |
| 8 | VDD | Power Supply for Logic This is a voltage supply pin. It must be connected to external source. |
| 9 | RES# | Power Reset for Controller and Driver This pin is reset signal input. When the pin is low, initialization of the chip is executed. |
| 10 | SCL | Host Data Input/Output Bus When serial mode is selected, D1 will be the serial data input SDIN and D0 will be the serial clock input SCLK. When I2C mode is selected, D2 & D1 should be tired together and serve as SDAout & SDAin in application and D0 is the serial clock input SCL. |
| 11 | SDA | |
| 12 | IREF | Current Reference for Brightness Adjustment This pin is segment current reference pin. A resistor should be connected between this pin and VSS. Set the current lower than 12.5μA. |
| 13 | VCOMH | Voltage Output High Level for COM Signal This pin is the input pin for the voltage output high level for COM signals. A capacitor should be connected between this pin and VSS. |
| 14 | VCC | Power Supply for OEL Panel This is the most positive voltage supply pin of the chip. A stabilization capacitor should be connected between this pin and VSS when the converter is used. It must be connected to external source when the converter is not used. |
Dane mechaniczne
| Rzecz | Wymiar | Jednostka |
|---|---|---|
| Matryca punktowa | 64 × 32 | Dots |
| Wymiary modułu | 14.5 × 11.6 × 1.26 | mm |
| Obszar aktywny | 11.18 × 5.58 | mm |
| Wielkość piksela | 0.153 × 0.153 | mm |
| Raster pomiędzy pikselami | 0.175 × 0.175 | mm |
| Tryb wyświetlania | matryca | |
| Kolor wyświetlacza | Monochromatyczny | |
| Drive Duty | 1/32 Duty | |
| IC | SSD1306 | |
Bezwzględne oceny maksymalne
| Parameter | Symbol | Minimalna wartość | Maksymalna wartość | Jednostka |
|---|---|---|---|---|
| Supply Voltage for Logic | VDD | 0 | 4 | V |
| Supply Voltage for Display | VCC | 0 | 15 | V |
| Temperatura pracy | TOP | -40 | +80 | °C |
| Temperatura przechowywania | TSTG | -40 | +80 | °C |
Parametry elektryczne
| Rzecz | Symbol | Stan | Minimalna wartość | Typowa wartość | Maksymalna wartość | Jednostka |
|---|---|---|---|---|---|---|
| Supply Voltage for Logic | VDD | － | 2.8 | 3 | 3.3 | V |
| Supply Voltage for Display | VCC | － | 7 | 7.5 | 7.8 | V |
| Input High Volt. | VIH | － | 0.8×VDD | － | VDDIO | V |
| Input Low Volt. | VIL | － | 0 | － | 0.2×VDD | V |
| Output High Volt. | VOH | － | 0.9×VDD | － | VDDIO | V |
| Output Low Volt. | VOL | － | 0 | － | 0.1×VDD | V |
| 50% Check Board operating Current | ICC | VCC=7.5V | － | 5 | 20 | mA |
Search keyword: 64x32 oled, oled 64x32,0.49 oled, 0.49" oled, 0.49 inch oled, oled 0.49, oled 0.49"
