N° de modèle WEO128128D-CTP

►Type: Graphique
►Structure: COG
►Dimension: 1.18 pouces
►Matrice de points 128x128
►Contrôleur intégré SSD1327
►Alimentation 3V
►1/128 duty
►Interface: SPI, I2C
►Avec dalle tactile capacitive (CTP)
►Detect Point : 1 Finger
►Couleur d'affichage: Blanc / Jaune / Bleu ciel (have high MOQ)
►Support Grayscale

Téléchargement PDF

DEMO CODE

Ajouter à demande

PRÉC. Retour à la liste SUIVANT

DESCRIPTION

DESSIN

1.18" 128x128 Round OLED Display Module with Touch Screen - WEO128128D-CTP

Data source ref: WEO128128DWPP3D00001

SPÉCIFICATIONS

Fonction PIN sur l'interface

No.

Symbole

Function

VSS

Ground pin. It must be connected to external ground.

VCC

Power supply for panel driving voltage. This is also the most positive power voltage supply pin. It is supplied by external high voltage source.

VCOMH

COM signal deselected voltage level.
A capacitor should be connected between this pin and VSS. No external power supply is allowed to connect to this pin.

VCI

Low voltage power supply and power supply for interface logic level. It should match with the MCU interface voltage level and must be connected to external source.
VCI must always set to be equivalent to or higher than VDD.

VDD

Power supply pin for core logic operation.

BS1

MCU bus interface selection pins. Select appropriate logic setting as described in the following table. BS1 is pin select.
Bus Interface selection

BS1	Interface
0	4-line SPI
1	I2C

Note (1) 0 is connected to VSS (2) 1 is connected to VCI

IREF

This pin is the segment output current reference pin

CS#

This pin is the chip select input connecting to the MCU.
The chip is enabled for MCU communication only when CS# is pulled LOW (active LOW).

RES#

This pin is reset signal input.
When the pin is pulled LOW, initialization of the chip is executed.
Keep this pin pull HIGH during normal operation.

DC#

This pin is Data/Command control pin connecting to the MCU.
When the pin is pulled HIGH, will be interpreted as data.
When the pin is pulled LOW, will be transferred to a command register
In I2C mode, this pin acts as SA0 for slave address selection.

When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN and D2 should be kept NC.
When I2C mode is selected, D2, D1 should be tied together and serve as SDAout , SDAin in application and D0 is the serial clock input, SCL.

TP_SCK

I2C clock signal

TP_SDA

I2C data signal

TP_INT

Interrupt signal

VCC

Power supply for panel driving voltage. This is also the most positive power voltage supply pin.

VSS

Ground

Données mécaniques

Article	Dimensions	Unité
Matrice de points	128 × 128	Dots
Dimensions du module	Ø50.5 × 5.0	mm
Zone active	Ø30.0	mm
Pixel Size	0.210 × 0.210	mm
Pixel Pitch	0.235 × 0.235	mm
Mode d'affichage	Matrice passive
Couleur d'affichage	Monochrome
Drive Duty	1/128Duty
Gray Scale	4 bits
IC	SSD1327
Interface double ligne	4-line SPI , I2C
Diagonale	1.18 pouces

PCAP IC	IT7259
Detect Point	1
PCAP Interface	I2C
PCAP Surface Hardness	6H

Valeurs nominales maximales absolues

Parameter	Symbole	Min	Max	Unité
Supply Voltage for Operation	VCI	-0.3	4.0	V
Supply Voltage for Logic	VDD	-0.5	2.75	V
Supply Voltage for Display	VCC	-0.5	19.0	V
Température de fonctionnement	TOP	-20	+50	°C
Température de stockage	TSTG	-30	+70	°C

Caractéristiques électroniques

DC Caractéristiques électroniques

Article	Symbole	État	Min	Typ	Max	Unité
Supply Voltage for Logic	VCI	－	2.8	3.0	3.3	V
Supply Voltage for Display	VCC	－	14.0	14.5	15.0	V
High Level Input	VIH	－	0.8×VCI	－	VCI	V
Low Level Input	VIL	－	0	－	0.2×VCI	V
High Level Output	VOH	Iout = 100uA	0.9×VCI	－	VCI	V
Low Level Output	VOL	Iout = 100uA	0	－	0.1×VCI	V
50% Check Board operating Current		VCC =14.5V	－	24	36	mA