12864, 2.42" Moduli OLED con pannello touch capacitivo
Modello numero WEO012864J-CTP
►Tipo :a caratteri
►Struttura: COG+PCB
►Dimensione: 2.42 pollici
►128 x 64 a matrice di punti
►A bordo Controllore SSD1309
►Alimentatore 3V
►1/64 duty
►Interfaccia: 8080 option 6800, SPI, I2C
►pannello touch capacitivo (CTP)
►Detect Point : 1 Finger
►Colore display: Bianco / Giallo / Cielo blu / Verde
DISEGNO
Data source ref: WEO012864JWPP3D00000
SPECIFICHE TECNICHE
Funzione dei Pin di Interfaccia
| No. | Simbolo | Funzione |
|---|---|---|
| 1 | VDD | Power supply pin for core logic operation |
| 2 | VSS | Ground. |
| 3 | NC(GND) | No connection |
| 4~11 | D0~D7 | These pins are bi-directional data bus connecting to the MCU data bus. Unused pins are recommended to tie LOW. |
| 12 | CS# | This pin is the chip select input connecting to the MCU. The chip is enabled for MCU communication only when CS# is pulled LOW (active LOW). |
| 13 | NC(GND) | No connection |
| 14 | RES# | This pin is reset signal input. When the pin is pulled LOW, initialization of the chip is executed. Keep this pin pull HIGH during normal operation. |
| 15 | R/W# | This pin is read / write control input pin connecting to the MCU interface. When 6800 interface mode is selected, this pin will be used as Read/Write (R/W#) selection input. Read mode will be carried out when this pin is pulled HIGH and write mode when LOW. |
| 16 | D/C# | This pin is Data/Command control pin connecting to the MCU. When the pin is pulled HIGH, the data at D[7:0] will be interpreted as data. When the pin is pulled LOW, the data at D[7:0] will be transferred to a command register. |
| 17 | E | This pin is MCU interface input. When 6800 interface mode is selected, this pin will be used as the Enable (E) signal. |
| 18 | NC(GND) | No connection |
| 19 | DISP | No Connection |
| 20 | NC(GND) | No connection |
| 21 | TP_INT | Interrupt signal, active low, asserted to request Host start a new transaction |
| 22 | TP_SDA | I2C data signal |
| 23 | TP_SCL | I2C clock signal |
| 24 | TP_RST | External reset signal, active low |
Dati meccanici
| Articolo | Dimensioni | Unità |
|---|---|---|
| A matrice di punti | 128 x 64 | － |
| Dimensione del modulo | 75.0 × 52.7 ×10.2 MAX | mm |
| Area attiva | 55.01 × 27.49 | mm |
| Dimensioni del Dot | 0.40 × 0.40 | mm |
| Passo del Dot | 0.43 × 0.43 | mm |
| Modalità display | Matrice passiva | |
| Colore display | Monocromatici | |
| Drive Duty | 1/64 Duty | |
| IC | SSD1309 | |
| Interfaccia | 8Bits 6800 , opzionale 8080 / 4-SPI / I2C | |
| Dimensioni | 2.42 pollici | |
| PCAP IC | GT911 | |
| Detect Point | 1 | |
| PCAP Interfaccia | I2C | |
| Superficie | Bagliore (Glare) | |
Valori massimi assoluti
| Parameter | Simbolo | Valore Min | Valore massimo | Unità |
|---|---|---|---|---|
| Supply Voltage for Logic | VDD | -0.3 | 4 | V |
| Temperatura di lavoro | TOP | -20 | +70 | °C |
| Temperatura di stock | TSTG | -30 | +80 | °C |
Caratteristiche elettriche
DC Caratteristiche elettriche
| Articolo | Simbolo | Condizione | Valore Min | Valore tipico | Valore massimo | Unità |
|---|---|---|---|---|---|---|
| Supply Voltage for Logic | VDD | － | 2.8 | 3.0 | 3.3 | V |
| High Level Input | VIH | － | 0.8×VDD | － | － | V |
| Low Level Input | VIL | － | － | － | 0.2×VDD | V |
| High Level Output | VOH | － | 0.9×VDD | － | － | V |
| Low Level Output | VOL | － | － | － | 0.1×VDD | V |
| 50% Check Board operating Current | IDD | VDD =3V | - | 150 | 300 | mA |
Search keyword: 128x64 oled, oled 128x64, 2.42 oled, 2.42" oled, 2.42 pollici oled, oled 2.42, oled 2.42"
